Bathroom vessel sink install

Coat the drain hole with a bead of waterproof sealant. Thread the drain into the vanity below from the vessel sink, using the right drain model. The drain should rest in the hole with a snug fit.

You should use a generous amount of sealant to ensure that the drain is fixed and sealed completely. Right under your vanity also, your other mechanisms including rubber gaskets should fit firmly to the bottom of the sink.

Avoid overtightening the drain because it can lead to complications or even cracks if the vessel sink is made out of materials like ceramic or glass. During sink installation, the usual practice is to install the faucet on its own without the sink bowl. But the drainage system below remains attached to the spigot and its handle. At this point, you are to install the faucet as instructed by the manufacturer, whether it is a single-lever faucet or a double-handled one.

Make sure that the hot and cold lines are correctly attached to the appropriate handles. Use as much sealant as necessary in order to prevent any eventual seepage or leaks. In the process of installing your bathroom vessel sink, your drain has to eventually be connected to the sink bowl. Go ahead and look below the vanity after you have installed the upper part of the drain securely.

If you find the drain pipe too long compared to the space under the vanity, you can reduce the length using your hacksaw. The pipe that extends from the bottom of the drain should be connected to a P-trap. Thread each pipe at the end so that they easily screw one onto another. Join the other end of the P-trap to the main pipe which is attached to your wall. You can as well secure each item tightly using your wrench. Bathroom Faucets Browse All.

Kitchen Accessories Browse All. Bathroom Accessories Browse All. Bathroom Drains Mounting Rings. Faucet Accessories Browse All. Base Plates Soap Dispensers. Pro Care Browse All. Repair Kits Cleaning and Maintenance.

Sink Model Number. Warranty Information Certifications Shipping. If it doesn't, use non-hardening plumbers' putty or silicone to create the seal. Install the gasket, the included cardboard washer, and the locknut to secure the tailpiece. Part 3. Make sure the water lines match the new fixture. If you put two pipe threads together, splice them with teflon tape. Connect the water supply lines. Water supply lines should screw into place with the corresponding joints on the new faucet.

The specific size of the connectors should be included in the instructions for the specific faucet that you're installing. Lines also need to be long enough so you won't put stress on the joints. Better to have extra long lines and have them loop. No hard bends or kinks. Make them hand tight, and somewhere around a quarter to half turn with a wrench.

Usually the "female" connection piece on both ends will always have rubber gaskets, so you don't need teflon tape. Connect the pop-up. The pop-up is the device that allows you to open and close the sink drain, usually made of a simple metal rod with ball attached to it. Drop stopped into sink from top, slide short end of rod into the opening on the tailpiece, making sure that the opening for the ball is facing toward the lever for the pop-up.

Install as per the instructions. Sometimes you need washers and sometimes you don't. Slide nut to trap the ball in the tailpiece. Tighten so there's no wiggle, but not so tight that it's difficult to raise and lower.

Attach thumbscrew to pop-up lever rod while sliding the rod from the ball so they can attach and allow you to screw together. Seal your connections with silicone caulk. Finish with silicon around the top of the sink, anywhere that the basin of the sink meets the wall, filling any gaps with a thin bead of caulk.

Let the caulk dry for about 24 hours before turning on the water and going back over your work to check for leaks. Turn on the water and check for leaks. There's no way to know if something is going to leak until you turn the water on. If you have small leaks from the rubber connections, try tightening more. The drain itself will also sometimes leak, which can be caused by over-tightening and straining the seal created by the connector gaskets.

If that's leaking, don't go past hand tight. Try a new washer instead. It's also a good idea to check the gasket that goes under the tailpiece. Try tightening the nut down more or try different washer or silicone. Does the sink need to be connected to the vent in the wall? If so, how is that done? The tailpiece should be connected to the P-trap, which is connected to your drainage system. That will create the connection to the venting in the wall. Not Helpful 14 Helpful 6. These are for the sink's overflow.

Not every sink has an overflow anymore, and most that do no longer plumb it in this fashion. Not Helpful 20 Helpful 8. No, not that I've ever seen. Most don't even have a manufacturer or model either. Not Helpful 13 Helpful 5.

When I turn on the water in the sink or flush the toilet in my master bath, I have a leak down in the basement. What are the pros and cons of vessel sinks? How high should a vanity be with a vessel sink?

How high should faucets be above a vessel sink? Read more to find the answers to all of these questions! Style: Vessel sinks are a status symbol of luxury and sophistication. Installation: Since vessel sinks sit on top of the vanity, installation is easier because you can avoid costly and difficult sink cut-outs.

You need to only cut one hole for the drain. Flexibility: Because vessel sinks sit on top of the vanity, they are not stuck in a place like inset sinks are and can be changed out relatively easily. This is even truer considering that installation is fairly easy, as well. Vessel sinks are thus a great idea to consider in a bathroom remodel. Space: Although not much, you gain a little bit more counter space with a vessel sink. Durability: Because the basin is exposed, your sink is more prone to chipping, cracking, and breakage, especially at the edges.

Cleaning: Vessel sinks are more difficult to clean, especially at the bottom of the basin where the sink meets the countertop. Moreover, stains and other marks will be more visible simply because the basin is showing and exposed.

Since cleaning the back and base of the vessel sink can be tricky, make sure to leave enough room between the sink and the wall during installation. You can add greater basin stability by opting for a recessed vessel sink more on that later.

Splashing: A common problem that people complain about with vessel sinks is splashing. We will touch more on this problem later. Overflow: Most vessel sinks do not come with overflow drains, which means that water will drain a bit more slowly and is more likely to overflow, especially considering that vessel sinks are typically more shallow and prone to splashing.

As you can see, vessel sinks come with their pros and cons. If you want the look and style of a vessel sink but are worried about the impracticalities, consider placing a vessel sink in decorative, lower-traffic bathrooms, like powder rooms or guest bathrooms.

Vessel sinks come in a wide variety of styles, colors, and materials, such as ceramic, glass, stone, copper, marble, wood, and steel. Ceramic and glass vessel sinks are the most popular and common types. Of course, each material comes with its pros and cons. Some materials will be harder to maintain than others and will be more prone to breakage or staining, like clear glass, wood, and stone.